Motorcycle parts look new little trick
Release time:
2024-09-20
1. Skillfully Remove Old Decals In the renovation and repair of motorcycles, some body decals often become old and hairy, but it is difficult for you to take them off.
1. Skillfully remove old decals
In the renovation and repair of motorcycles, some body decals often become old and hairy, but it is difficult for you to take them off. There is a way here, that is, the decal is soaked in water for 301min or so to make it wet, then the eraser used for drawing is dipped in a little washing powder solution and rubbed on the decal. After a while, the decal and some dirt are rubbed into strips and fall off. Then rinse the surface of the car with water.
2. Maintenance of electroplating parts
Electroplating layer most corrosive solution, in organic acid is stable, can maintain long-term luster. However, the following conditions will make the plating layer corroded, need to pay attention to and take measures to protect.
1, should prevent contact with salt, hydrochloric acid, bittern and other substances. Because the coating is easily soluble in the above substances, it is necessary to avoid contact with 84 disinfectant, bleaching powder, toilet cleaning and other substances.
2. Do not store motorcycles in places with gas, briquettes and soot. This is because carbon monoxide (CO) will cause the coating to produce gray black network cracks and rust.
3, pay attention to the method of wiping. Usually in a week only on the motorcycle plating wipe a neutral oil, such as sewing machine oil. Note that every time you wipe the oil, you should first wipe the dust with a soft cloth; after driving in rainy days, you should first wipe the dirt with clean water; then wipe with a soft cloth, and finally dip in engine oil to wipe. When wiping oil, do not touch the oil on the paint surface and tires to prevent the paint surface from losing gloss and tire aging. If there is water mist inside the instrument and other coatings, it should be dried with a hair dryer before wiping.
4. For the galvanized surface on the car strip, a layer of dark gray basic zinc carbonate film is formed on the surface, which can effectively prevent the internal metal from being corroded, so pay attention to the dark gray when wiping. The galvanized surface can be wiped clean and polished, and some neutral engine oil can be wiped to protect it.
5. For the wiping of plastic electroplating parts, only a soft cloth dipped in water (warm water) can be wiped, not dipped in engine oil, because it will destroy the coating of plastic electroplating parts.
6. For plated parts such as exhaust pipes, fenders, and rims, you cannot brush the mud with a steel wire brush, because the wire of the wire brush will scratch the surface of the coating. Apply clear water to loosen the mud and then wipe it according to the above method. If the bubble is not loose, apply the wooden bar to remove the scale gently.
3. Oil drum sealing method
At present, most motorcycle users use plastic drums to hold gasoline, which are moderately expensive and more convenient. However, the barrel cover is often not tightly sealed, and gasoline is easy to volatilize, causing both waste and insecurity. My solution to this problem is to cover the barrel with a layer of convenient plastic bags before covering the barrel lid, and then tighten the barrel lid. In order to check whether the seal is good, you can squeeze the plastic barrel by hand. If there is no air leakage, the barrel cover is sealed.
4. Cleaning of non-metallic parts
In the maintenance of motorcycles, it is often encountered that some non-metallic parts need to be cleaned. These parts can not be used to clean metal parts of kerosene, diesel, gasoline and metal cleaning agent to clean, otherwise, will cause deterioration and failure. The cleaning method should be determined according to the material of the parts.
(1) rubber parts, the application of alcohol cleaning.
(2) Parts made of foam plastic shall be cleaned with washing powder or soapy water.
(3) leather parts should not be washed with any cleaning liquid, can be wiped with a cloth.
(4) paper parts can not be washed with water, the application of brush brush, or in kerosene, diesel oil cleaning.
(5) Clutch friction linings and brake shoe friction linings cannot be cleaned with kerosene, diesel, or alkali solution, and should be brushed with gasoline.
Related News
CHONGQING YONGFENG ELITE AUTO PARTS CO., LTD.
Address: No.23, Jiu'yang Rd., Nan'jin Subdistrict, He'chuan District
Tel: +86023-42815139
CHONGQING YONGFENG ELITE VALVE CO.,LTD.
Address: No.68 Ankang sub Rd.Airport Industrial parkYubei District Chongqing,401120,PRC
Tel: +86023-42815178
©2024 Chongqing Yongfeng Jingqi Auto Parts Co., Ltd.
Powered by www.300.cn | SEO [Privacy Statement]
Business License